超细羊毛低损伤梳毛加工技术

纺织学报 ›› 2016, Vol. 37 ›› Issue (05): 23-27.

超细羊毛低损伤梳毛加工技术

收稿日期:2015-06-23 修回日期:2016-01-21 出版日期:2016-05-15 发布日期:2016-05-10

Low-damage carding technology of superfine wool

Received:2015-06-23 Revised:2016-01-21 Online:2016-05-15 Published:2016-05-10

摘要/Abstract

摘要：

为解决13.0 μm以下的超细羊毛加工困难和梳理损伤严重的问题，提高其使用价值，对梳毛损伤进行成因分析并探讨解决办法。通过对梳毛各工作区的纤维长度、毛粒数、落毛率的测定，利用TEAM-3预测公式和正交试验法，优化各工艺参数，确定了隔距、速比、锡林针布齿密、道夫针布齿密、出条重量等梳毛工艺的最优配置条件，其中2#隔距、3#速比，针布规格为60.7 齿/cm2锡林针布齿密，道夫针布齿密为62.5 齿/cm2，出条重量为20 g/m。经过验证，利用此低损伤梳毛工艺制成的超细羊毛精梳毛条，纤维长度平均损伤小于0.5 mm，毛粒减少，条干明显改善。

关键词: 超细羊毛, 梳毛, 低损伤, 优化

Abstract:

In order to solve the problems of difficulty processing and carding damage of the superfine wool, the paper analyzed the causes and solutions to thecarding damage. Through the measurement of fiber length, the number of neps, noil ratio in work space of combing, the carding process parameters were optimized, the optimal carding processing conditions were determined by TEAM-3 and orthogonal experiments as following: 2# gauge, 3# speed ratio, the tooth density of cylinder wire cloth and doffer wire cloth was 60.7 teeth/cm2 and 62.5 teeth/cm2, respectively, and top produced was 20g/m. The experimental results showed that the average loss of fiber length of the superfine wool tops derived from the optimal processing wasless than 0.5 mm. The number of neps was also decreased and yarn quality was improved.

Key words: superfine wool, carding, low-damage, optimization

丁彩玲俞建勇张瑞云李慧程隆棣秦光. 超细羊毛低损伤梳毛加工技术[J]. 纺织学报, 2016, 37(05): 23-27.

参考文献

相关文章 15

[1]	李冻陈太球蒋春燕傅佳佳王鸿博. 原料及结构参数对防电弧织物性能的影响[J]. 纺织学报, 2018, 39(08): 41-45.
[2]	孙影慧杜劲松. 服装单件流水线的Flexsim仿真[J]. 纺织学报, 2018, 39(06): 155-161.
[3]	颜苏芊王力平. 喷气织机中压缩空气的泄漏评估及其修复优化[J]. 纺织学报, 2018, 39(04): 130-136.
[4]	周俊荣江励. 高速电脑绣花机结构优化设计[J]. 纺织学报, 2018, 39(01): 133-138.
[5]	韩瑞叶杨瑞华薛元高卫东. 数码转杯纺的Stearns-Noechel配色模型[J]. 纺织学报, 2017, 38(12): 27-32.
[6]	郭隽侠陶建峰刘成良. 应用改进蚁群算法的同心分布喷丝孔检测路径规划[J]. 纺织学报, 2017, 38(11): 124-130.
[7]	杜玉红杨程午蒋秀明刘仁杰蔡文超. 应用聚类神经网络的异纤检测多类光源优化设计[J]. 纺织学报, 2017, 38(10): 104-112.
[8]	刘宜胜徐海亮吴震宇袁嫣红. 三维编织机运动仿真分析及其轨道优化设计[J]. 纺织学报, 2017, 38(04): 134-139.
[9]	刘笑莹方斌朱守艾程隆棣张瑞云俞建勇. 棉/大麻纤维混纺低损耗工艺优化[J]. 纺织学报, 2017, 38(01): 35-39.
[10]	代丽梅谢春萍刘新金张洪. 莱赛尔纱超大牵伸纺纱工艺的优化[J]. 纺织学报, 2016, 37(3): 25-30.
[11]	尉苗苗李岳阳蒋高明丛洪莲. 应用最优Gabor滤波器的经编织物疵点检测[J]. 纺织学报, 2016, 37(11): 48-54.
[12]	蔡薇琦马崇启阚永葭杨金莲李君丽 . 酚醛纤维头道并条工艺优化及其对成纱质量的影响[J]. 纺织学报, 2016, 37(10): 26-31.
[13]	石春乐陈炜杨以雄 . 快时尚品牌产品开发流程对时间绩效的影响[J]. 纺织学报, 2016, 37(10): 113-119.
[14]	黄双郗欣甫徐洋孙以泽. 簇绒地毯织机耦联轴系的铰链间隙对毯面绒高的影响[J]. 纺织学报, 2016, 37(08): 132-137.
[15]	刘婵谢春萍刘新金曲华洋徐伯俊. 黑牦牛绒氧化脱色工艺优化及其可纺性[J]. 纺织学报, 2016, 37(07): 49-54.

Metrics

Viewed

Full text

Abstract

Cited

Shared

Discussed