纺织学报 ›› 2019, Vol. 40 ›› Issue (09): 108-113.doi: 10.13475/j.fzxb.20180904906

• 染整与化学品 • 上一篇    下一篇

纳米发泡整理对芳纶过滤材料性能的影响

缪特1, 张如全1,2(), 冯阳3   

  1. 1.武汉纺织大学 纺织科学与工程学院, 湖北 武汉 430200
    2.武汉纺织大学 纺织纤维及制品教育部重点实验室, 湖北 武汉 430200
    3.江苏奥凯环境技术有限公司, 江苏 靖江 214500
  • 收稿日期:2018-09-18 修回日期:2019-02-20 出版日期:2019-09-15 发布日期:2019-09-23
  • 通讯作者: 张如全
  • 作者简介:缪特(1993—),男,硕士生。主要研究方向为非织造材料。
  • 基金资助:
    武汉纺织大学产学研项目(1618);武汉纺织大学校基金项目(201711)

Influence of nano-foam finishing on properties of aramid filter materials

MIAO Te1, ZHANG Ruquan1,2(), FENG Yang3   

  1. 1. School of Textile Science and Engineering, Wuhan Textile University, Wuhan, Hubei 430200, China
    2. Key Laboratory of Textile Fibers and Products, Ministry of Education, Wuhan Textile University, Wuhan, Hubei 430200, China
    3. Jiangsu Okay Environmental Technology Co., Ltd., Jingjiang, Jiangsu 214500, China
  • Received:2018-09-18 Revised:2019-02-20 Online:2019-09-15 Published:2019-09-23
  • Contact: ZHANG Ruquan

摘要:

为提高芳纶过滤材料的过滤效率,以添加不同质量分数纳米陶瓷粉的聚四氟乙烯乳液为涂层剂主要原料,采用发泡剂发泡涂层法对芳纶材料进行表面涂层处理。研究了泡沫涂层对芳纶过滤材料的结构、耐摩擦性、透气性、孔径大小、拒水拒酸碱性以及过滤性能的影响。结果表明:经发泡涂层整理后,芳纶表面形成一层致密薄膜;纳米陶瓷粉质量分数越大,发泡剂发泡效果越好,薄膜愈致密且稳定,同时芳纶过滤材料的耐摩擦性愈好,其孔径大小及透气性略有下降;涂层提高了芳纶的拒酸、拒碱性能,有效减少了滤袋的糊袋,使其清灰性及使用寿命均有所提升;涂层后芳纶的过滤效率显著提高,过滤直径为1 μm以上颗粒物的过滤效率由39.1%提升到60%左右,且过滤直径为10 μm以上颗粒物的过滤效率可达到100%。

关键词: 聚四氟乙烯乳液, 泡沫涂层, 耐高温过滤材料, 纳米陶瓷粉, 芳纶, 过滤效率

Abstract:

In order to improve the filtration efficiency of the aramid filter material, the polytetrafluoroethylene (PTFE) aqueous emulsion was used as the main raw material to conduct coating treatment on the surface of aramid filter material by foam coating method. The influence of foam coating on the structure, friction resistance, air permeability, pore size, hydrophobicity, acid and alkali resistance, and the filtration performance of the filter material were studied. The test results show that a dense film is formed on the surface of the filter after foamed coating. With the increase of the amount of ceramic powder, the foaming effect of the coating solution becomes better, and film formed on the surface of the filter material is denser. Besides, the friction resistance performance of filter material is improved as well as the air permeability slightly decreases. The coating treatment not only improves the acid and alkali resistance and ash removal performance of the filter material and prolonged its service life, but also reduces dust attachment. The filtration performance test shows that the filtration efficiency of the filter material after coating has a remarkable improvement, and the filtration efficiency for the particulate matter above 1 μm increases from 39.1% to 60%, and particulate matter above 10 μm is filtrated by 100%.

Key words: polytetrafluoroethylene emulsion, foam coating, high temperature resistant filter material, ceramic nanopowder, aramid fiber, filtration efficiency

中图分类号: 

  • TS174.3

表1

不同摩擦次数时芳纶过滤材料的质量差"

过滤材料 0次 1 000次 2 000次 5 000次
未涂层 5.39 5.38 5.36 5.33
PTFE涂层 6.51 6.51 6.50 6.50
0.5%陶瓷粉涂层 6.88 6.88 6.87 6.87
1.0%陶瓷粉涂层 6.51 6.51 6.50 6.49

图1

涂层前后芳纶过滤材料扫描电镜照片(×500)"

图2

涂层前后芳纶的红外光谱图"

图3

不同整理过滤材料拒水接触角"

图4

不同整理过滤材料的拒酸接触角"

图5

不同整理过滤材料拒碱接触角"

表2

涂层前后芳纶过滤材料透气性"

过滤材料 正面透气量 透气量下降量
未涂层 485.4
PTFE涂层 350.2 135.2
0.5%陶瓷粉涂层 322.9 162.5
1.0%陶瓷粉涂层 316.5 168.9

表3

涂层前后孔径测试结果"

过滤材料 最小孔径 最大孔径 平均孔径
未涂层 8.5 62.6 23.4
PTFE涂层 6.5 33.4 14.7
0.5%陶瓷粉涂层 5.8 33.0 13.3
1.0%陶瓷粉涂层 5.4 31.2 12.5

图6

过滤材料对不同粒径颗粒物的过滤效率"

[1] 李永光, 刘颖. 发泡涂层针刺毡的过滤性能研究[J]. 纺织导报, 2016(1):84-85.
LI Yongguang, LIU Yin. To analysis the high efficiency filtration performance of needle-felt foam coating technology[J]. China Textile Leader, 2016(1):84-85.
[2] 王成, 姚理荣, 陈宇岳. 芳纶纳米纤维毡/聚苯硫醚高温超过滤材料的制备及其性能[J]. 纺织学报, 2013,34(7):1-4.
WANG Cheng, YAO Lirong, CHEN Yuyue. Preparation and properties of high temperature resistant ultrafiltration aramid nanofiber/PPS composite material[J]. Journal of Textile Research, 2013,34(7):1-4.
[3] ZHANG Rufan, LIU Chong, HSU Pochun. Nanofiber air filters with high temperature stability for efficient PM2.5 removal from the pollution sources[J]. Nano Lett, 2016,16(6):3642-3649.
doi: 10.1021/acs.nanolett.6b00771 pmid: 27167892
[4] 蔡伟龙, 郑玉婴, 肖向荣. 聚酰亚胺/聚四氟乙烯复合过滤材料的发泡涂层性能[J]. 纺织学报, 2011,32(4):29-32.
CAI Weilong, ZHENG Yuying, XIAO Xiangrong. Properties of foam coated surface of polyimide/PTFE composite filtering material[J]. Journal of Textile Research, 2011,32(4):29-32.
[5] 余琴, 邓炳耀, 刘庆生, 等. 纳米Si02/PTFE乳液整理对聚苯硫醚滤料性能的影响[J]. 纺织学报, 2013,34(11):77-81.
YU Qin, DENG Bingyao, LIU Qingsheng, et al. Study on PPS nonwoven filter material impregnated by nano Si02/PTFE emulsion to improve its performance[J]. Journal of Textile Research, 2013,34(11):77-81.
[6] 周冠辰, 于斌, 韩建, 等. 玄武岩纤维/聚苯硫醚针刺复合滤料的聚四氟乙烯乳液处理[J]. 纺织学报, 2014,35(8):10-14.
ZHOU Guanchen, YU Bin, HAN Jian, et al. PTFE emulsion processing of needled basalt / PPS composite filters[J]. Journal of Textile Research, 2014,35(8):10-14.
[7] PARK B H, LEE M H, KIM S B, et al. Preparation and characterization of porous composite filter medium by polytetrafluoroethylene foam coating[J]. Journal of the Air and Waste Management Association, 2010, 60(2):137-141.s.
doi: 10.3155/1047-3289.60.2.137 pmid: 20222525
[8] 束华东, 李小红, 张治军. 表面修饰纳米二氧化硅及其与聚合物的作用[J]. 化学进展, 2008,20(10):1509-1514.
SHU Huadong, LI Xiaohong, ZHANG Zhijun. Surface modified nano-silica and its action on polymer[J]. Progress in Chemistry, 2008,20(10):1509-1514.
[9] 黄学亮, 张华鹏, 朱海霖, 等. 针刺过滤材料的表面精细化处理[J]. 浙江理工大学学报, 2012,29(5):646-649.
HUANG Xueliang, ZHANG Huapeng, ZHU Hailin, et al. Surface treatment of a needle-punched filter material by foam coating[J]. Journal of Zhejiang Sci-Tech University, 2012,29(5):646-649.
[10] 崔运花, 韩雅岚. 涤纶针刺滤料的PTFE乳液整理工艺探索[J]. 产业用纺织品, 2013,7(6):37-43.
CUI Yunhua, HAN Yalan. Research on the PTFE emulsion finishing of polyester needle punched nonwoven filter material[J]. Technical Textiles, 2013,7(6):37-43.
[11] 马德刚, 郑琪琪. 预涂层技术对滤料除尘性能的改进特性研究[J]. 天津大学学报, 2016,49(8):869-874.
MA Degang, ZHENG Qiqi. Modification of dust removal performance of filter media by precoating technology[J]. Journal of Tianjin University, 2016,49(8):869-874.
[12] GUTMAHER A, SLOKAR M, LOBNIK A, et al. A new slovenian konus-konex filter material for high-temperature filtration[J]. Fibres and Textiles in Eastern Europe, 2001,9(2):74-76.
[13] 殷依华, 于斌, 韩建. 后处理工艺对聚苯硫醚滤料清灰性能的影响[J]. 纺织学报, 2016,37(8):16-20.
YIN Yihua, YU Bin, HAN Jian. Influence of post-treatment process on dust cleaning performance of polyphenylene sulfide filters[J]. Journal of Textile Research, 2016,37(8):16-20.
[1] 杨小兵, 程钧, 张守鑫, 姚红, 陆林, 丁松涛. 口罩过滤效率检测用颗粒物粒径的换算和标准比对[J]. 纺织学报, 2020, 41(08): 152-157.
[2] 马飞飞. 离散树脂成型复合材料的防刺与服用性能[J]. 纺织学报, 2020, 41(07): 67-71.
[3] 许黛芳. 磷酸改性芳纶对聚氨酯硬质泡沫阻燃抑烟性能的影响[J]. 纺织学报, 2020, 41(05): 30-37.
[4] 胡铖烨, 缪润伍, 韩潇, 洪剑寒, GIL Ignacio. 聚乙烯醇对芳纶复合纱聚苯胺导电层耐久性影响[J]. 纺织学报, 2020, 41(04): 91-97.
[5] 李聃阳, 王瑞, 刘星, 张淑洁, 夏兆鹏, 阎若思, 代二庆. 剪切增稠液对不同结构芳纶织物防刺性能的影响[J]. 纺织学报, 2020, 41(03): 106-112.
[6] 庄群, 张飞, 杜兆芳, 姜华. 改性芳纶与环氧树脂复合体的制备及其防刺性能[J]. 纺织学报, 2019, 40(12): 98-103.
[7] 王璐, 丁笑君, 夏馨, 王虹, 周小红 . SiO2气凝胶/ 芳纶非织造布复合织物的防护功能[J]. 纺织学报, 2019, 40(10): 79-84.
[8] 吴利伟, 王伟, 林佳弘, 姜茜. 芳纶/超高分子量聚乙烯织物增强聚氨酯夹芯复合材料制备及其力学性能[J]. 纺织学报, 2019, 40(07): 64-70.
[9] 邹志伟, 钱晓明, 钱幺, 赵宝宝, 朵永超. 油剂去除对针刺非织造过滤材料驻极性能的影响[J]. 纺织学报, 2019, 40(06): 79-84.
[10] 胡雪敏 杨文秀 李腾. 氧化石墨烯/ 聚偏二氟乙烯复合纤维过滤膜的制备及其过滤性能[J]. 纺织学报, 2019, 40(04): 32-37.
[11] 缪润伍, 金丽华, 魏祺煜, 韩潇, 洪剑寒. 多轴向导电芳纶增强复合材料及其电磁屏蔽性能[J]. 纺织学报, 2019, 40(02): 100-104.
[12] 张美玲 沈忆文 王瑞 李先锋 郑广伟. 芳纶纤维的冷等离子体处理及其老化性能[J]. 纺织学报, 2018, 39(11): 73-78.
[13] KHAN Monir MUHAMMAD Ali 方小银 周熠. 纱罗组织对芳纶织物交织阻力的影响 [J]. 纺织学报, 2018, 39(11): 38-44.
[14] 尉霞 逯凯美 董晓宁. 间位芳纶织物的导湿排汗整理[J]. 纺织学报, 2018, 39(05): 80-86.
[15] 于宾 赵晓明 漆东岳. 腈纶预氧化丝/芳纶针刺滤材的性能[J]. 纺织学报, 2018, 39(03): 61-66.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
No Suggested Reading articles found!