Journal of Textile Research ›› 2019, Vol. 40 ›› Issue (05): 84-90.doi: 10.13475/j.fzxb.20180503707

• Dyeing and Finishing & Chemicals • Previous Articles     Next Articles

Influence of ink-jet printing pretreatment on fabric structures

YANG Haizhen1, FANG Kuanjun1,2(), LIU Xiuming1, CAI Yuqing3, AN Fangfang1, HAN Shuang1   

  1. 1. School of Textile Science and Engineering, Tianjin Polytechnic University, Tianjin 300387, China
    2. Collaborative Innovation Center for Eco-Textiles of Shandong Province, Qingdao, Shandong 266071, China
    3. College of Textiles and Clothing, Qingdao University, Qingdao, Shandong 266071, China
  • Received:2018-05-14 Revised:2018-12-10 Online:2019-05-15 Published:2019-05-21
  • Contact: FANG Kuanjun E-mail:13808980221@163.com

Abstract:

In order to study the relationship between fabric weave structure on the ink-jet printing effect, the plain, twill and honeycomb fabrics were selected as the research objects, and the same cold pad-batch treatment, pretreatment and ink-jet printing were performed on the three fabrics. The roughness, thickness, porosity, color strength and outline sharpness of fabrics were measured. The influence of pretreatment on fabric structures and the relationship between fabric structures and color strength and outline sharpness were analyzed. The results show that the warp roughness, weft roughness, thickness, and porosity of the plain fabric are 6.4 μm, 9.1 μm, 0.65 mm and 85.5%, respectively. Those of the twill fabric are increased by 22%, 30%, 25% and 2.5% compared with those of the plain fabric, respectively. While those of the honeycomb fabric are increased by 50%, 53%, 150%, and 3.4% compared with those of the plain fabric, respectively. The warp roughness, weft roughness and porosity of plain, twill, and honeycomb fabrics after cold pad batching and pretreatment are reduced, but fabric thickness is increased. In addition, the plain fabrics exhibit the lightest color strength and the best outline sharpness, followed by twill and honeycomb fabrics, which display the darkest color strength and the worst outline sharpness after the same treatment.

Key words: ink-jet printing, pretreatment, fabric structure, roughness, porosity, color strength, outline sharpness

CLC Number: 

  • TS194.4

Tab.1

Roughness of fabrics with different structures"

织物组织 粗糙度/μm
经向 纬向
平纹 6.4 9.1
斜纹 7.8 11.8
蜂巢 9.6 13.9

Fig.1

Roughness of fabrics before and after cold pad-batch"

Tab.2

Thickness of fabrics before and after cold pad-batch"

织物组织 织物厚度/mm
冷轧堆处理前 冷轧堆处理后
平纹 0.65 0.71
斜纹 0.81 0.88
蜂巢 1.61 1.77

Tab.3

Porosity of fabrics before and after cold pad-batch"

织物组织 孔隙率/%
冷轧堆处理前 冷轧堆处理后
平纹 85.5 83.6
斜纹 87.6 85.6
蜂巢 88.4 86.5

Fig.2

Roughness of fabrics before and after pretreatment"

Tab.4

Thickness of fabrics before and after pretreatment"

织物组织 厚度/mm
预处理前 预处理后
平纹 0.71 0.79
斜纹 0.88 0.95
蜂巢 1.77 1.87

Tab.5

Rorosity of fabrics before and after pretreatment"

织物组织 孔隙率/%
预处理前 预处理后
平纹 83.6 81.7
斜纹 85.6 83.2
蜂巢 86.5 84.3

Fig.3

K/S values of ink-jet printed fabrics with different structures"

Fig.4

Outline sharpness of ink-jet printed fabrics with different structures. (a) In warp direction;(b) In weft direction"

[1] BAE J H, HONG K H, LAMAR T M. Effect of texture on color variation in inkjet-printed woven textiles[J]. Color Research and Application, 2015,40(3):297-303.
[2] LIU Z, FANG K, GAO H, et al. Effect of cotton fabric pretreatment on drop spreading and colour performance of reactive dye inks[J]. Coloration Technology, 2016,132(5):407-413.
[3] 房宽峻, 刘尊东, 陈伟, 等. 棉织物表面处理对活性染料喷墨印花的影响[J]. 纺织学报, 2015,36(2):128-132.
FANG Kuanjun, LIU Zundong, CHEN Wei, et al. Effect of fabric surface treatment on ink jet printing with reactive dyes[J]. Journal of Textile Research, 2015,36(2):128-132.
[4] WANG L, HU C, YAN K. A one-step inkjet printing technology with reactive dye ink and cationic compound ink for cotton fabrics[J]. Carbohydrate Polymers, 2018,197:490-507.
pmid: 30007639
[5] YANG H, FANG K, LIU X, et al. Effect of cotton cationization using copolymer nanospheres on ink-jet printing of different fabrics[J]. Polymers, 2018,10(11), 1219-1234.
[6] AKGUN M. Assessment of the surface roughness of cotton fabrics through different yarn and fabric structural properties[J]. Fibers and Polymers, 2014,15(2):405-413.
[7] AKGUN M. The effect of fabric balance and fabric cover on surface roughness of polyester fabrics[J]. Fibers and Polymers, 2013,14(8):1372-1377.
[8] AKGUN M. Assessment of the effect of fabric constructional parameters on surface roughness of wool fabrics[J]. Journal of The Textile Institute, 2015,106(8):845-852.
[9] BECERIR B, AKGUN M, ALPAY H R. Effect of some yarn properties on surface roughness and friction behavior of woven structures[J]. Textile Research Journal, 2016,86(9):975-989.
[10] MOONEGHI S A, VARKIYANI M H, SAHARKHIZ S. Study on fabric surface roughness and its influence on worsted fabric abrasion resistance[J]. Journal of Engineered Fibers and Fabrics, 2015,4(10):79-86.
[11] PCCREWS I A. Influence of fiber type and fabric porosity on the UPF of summer fabrics[J]. Aatcc Review, 2004,4(2):26-31.
[12] FAROOQ S, YOUSUFANI S A. Effect of inter yarn fabric porosity on dye uptake of reactive dyed cotton woven fabric[J]. Mehran University Research Journal of Engineering and Technology, 2015,3(34):265-272.
[13] 潘登, 胡吉永, 丁辛, 等. 基于频谱分析的织物粗糙感[J]. 东华大学学报(自然科学版), 2012,38(1):10-15.
PAN Deng, HU Jiyong, DING Xin, et al. Fabric roughness based on spectrum analysis[J]. Journal of Donghua University (Natural Science Edition), 2012,38(1):10-15.
[14] 黄锦波, 李启正, 葛彩虹, 等. 基于浮长线分析组织变化与织物厚度的关系[J]. 丝绸, 2013,50(2):39-41.
HUANG Jinbo, LI Qizheng, GE Caihong, et al. Analysis on relationship between weave alteration and thickness based on floats[J]. Journal of Silk, 2013,50(2):39-41.
[15] 张鹤誉, 郑振荣, 赵晓明, 等. 玻璃纤维交织织物的热传递数值模拟[J]. 纺织学报, 2015,36(3):28-31.
ZHANG Heyu, ZHENG Zhenrong, ZHAO Xiaoming, et al. Numerical simulation of heat transfer on glass fiber woven fabric[J]. Journal of Textile Research, 2015,36(3):28-31.
[16] 韩丽, 张占柱. 棉织物冷轧堆前处理氧漂活化剂的制备及其应用[J]. 纺织学报, 2015,36(6):64-67.
HAN Li, ZHANG Zhanzhu. Preparation and application of bleaching activator for cold pad pre-treatment of cotton fabric[J]. Journal of Textile Research, 2015,36(6):64-67.
[17] 向中林, 韩雪梅, 刘增祥, 等. 棉织物低温酶氧-浴前处理工艺[J]. 纺织学报, 2017,38(5):80-85.
XIANG Zhonglin, HAN Xuemei, LIU Zengxiang, et al. Low-temperature pretreatment of cotton fabric by combining enzyme treating and peroxide bleaching in one bath[J]. Journal of Textile Research, 2017,38(5):80-85.
[18] REMADEVI R, GORDON S, WANG X, et al. Investigation of the swelling of cotton fibers using aqueous glycine solutions[J]. Textile Research Journal, 2016,87(18):2204-2213.
[19] 叶皓华, 陈国强, 唐孝明. 改性丝胶在棉织物上的应用[J]. 纺织学报, 2011,32(8):87-91.
YE Haohua, CHEN Guoqiang, TANG Xiaoming. Application of modified sericin on cotton fabrics[J]. Journal of Textile Research, 2011,32(8):87-91.
[20] 刘尊东. 棉织物的聚合物改性与喷墨印花效果[D]. 天津: 天津工业大学, 2017: 16-18.
LIU Zundong. Polymer modification and ink-jet printing effect of cotton fabrics[D]. Tianjin: Tianjin Polytechnic University, 2017: 16-18.
[21] 周秋宝, 陈君莉, 沈一峰. 蚕丝织物组织结构对其表观颜色深度的影响[J]. 实验室研究与探索, 2010,29(6):40-44.
ZHOU Qiubao, CHEN Junli, SHEN Yifeng. The influence of the organizational structure on the apparent color depth of silk fabric[J]. Research and Exploration in Laboratory, 2010,29(6):40-44.
[22] 李敏, 赵影, 张丽平, 等. 涤纶针织物数码印花清晰度的影响因素[J]. 纺织学报, 2018,39(5):62-66.
LI Min, ZHAO Ying, ZHANG Liping, et al. Factors influencing printing accuracy of digital printing for knitted polyester fabric[J]. Journal of Textile Research, 2018,39(5):62-66.
[1] LIU Muli, YUAN Li, YANG Yali, LIU Junping, GONG Xue, YAN Yuchen. Influence of fabric weaves on characteristics of colored patterns in color-woven fabrics [J]. Journal of Textile Research, 2020, 41(09): 45-53.
[2] LI Danyang, WANG Rui, LIU Xing, ZHANG Shujie, XIA Zhaopeng, YAN Ruosi, DAI Erqing. Effect of shear thickening fluid on quasi-static stab resistance of aramid-based soft armor materials [J]. Journal of Textile Research, 2020, 41(03): 106-112.
[3] LIN Jiameng, WAN Ailan, MIAO Xuhong. Preparation and properties of polypyrrole / silver conductive polyester fabrics [J]. Journal of Textile Research, 2020, 41(03): 113-117.
[4] ZHANG Yue, HU Danling, REN Jinna, LI Qing. Scouring and bleaching of cotton fabric by low temperature near neutrality one-bath one-step process [J]. Journal of Textile Research, 2019, 40(09): 83-90.
[5] HAN Jianjian, HU Yongjie, HU Minzhuan. Decolorization pretreatment method of quality inspection extraction solution based on nanofiltration technology [J]. Journal of Textile Research, 2019, 40(09): 136-142.
[6] GAO Jing, WANG Lu. Influence of pretreatment process on superhydrophobic modification of wool/polyester fabric [J]. Journal of Textile Research, 2019, 40(09): 91-96.
[7] ZHANG Aidan, ZHOU Jiu. Color rendering characteristics of fabric structure based on halftone design of image color [J]. Journal of Textile Research, 2019, 40(09): 56-61.
[8] QIAN Haihong, WANG Hongbo, DU Jinmei, FU Jiajia, WANG Wencong. Water and oil repellent finishing of cotton fabric based on fluoroacrylate miniemulsion [J]. Journal of Textile Research, 2019, 40(03): 83-89.
[9] LIU Sai, ZHENG Dongming, PAN Xingxing, LIU Gui, DU Zhaoqun. Formation and characterization of auxetic yarns with interlaced-helical structure and fabrics [J]. Journal of Textile Research, 2019, 40(02): 26-29.
[10] . Influence of pretreatment process on luffa fiber′s properties [J]. Journal of Textile Research, 2018, 39(12): 72-77.
[11] . Influence of full-color weave on color mixing law of compound fabric structure with triple-weft [J]. Journal of Textile Research, 2018, 39(10): 44-49.
[12] . Factors influencing printing accuracy of digital printing for knitted polyester fabric [J]. JOURNAL OF TEXTILE RESEARCH, 2018, 39(05): 62-66.
[13] . Influence of sizing pretreatment agent in properties of warp knitting cotton yarn  [J]. JOURNAL OF TEXTILE RESEARCH, 2018, 39(04): 82-86.
[14] . Synthesis of integrated polyurethane acrylate and application thereof in photo-curable ink-jet printing [J]. JOURNAL OF TEXTILE RESEARCH, 2018, 39(02): 97-105.
[15] . Optimization on antibacterial finishing process of cotton fabric based on electron beam irradiation [J]. JOURNAL OF TEXTILE RESEARCH, 2017, 38(10): 81-87.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
No Suggested Reading articles found!