Journal of Textile Research ›› 2024, Vol. 45 ›› Issue (02): 36-44.doi: 10.13475/j.fzxb.20220905401

• Fiber Materials • Previous Articles     Next Articles

Analysis on mechanical properties and fracture morphology of Xinjiang long-staple cotton fiber

MA Chengnuo1,2, JIANG Kaixiang1,2, CHEN Chunhui1,2, LIU Yuanling1,2, ZHANG Youqiang1,2()   

  1. 1. College of Mechanical and Electrical Engineering, Tarim University, Alar, Xinjiang 843300, China
    2. Key Laboratory of Modern Agricultural Engineering of Colleges and Universities, Department of Education of Xinjiang Uygur Autonomous Region, Tarim University, Alar, Xinjiang 843300, China
  • Received:2022-09-20 Revised:2023-03-23 Online:2024-02-15 Published:2024-03-29

RichHTML

10

PDF (PC)

86

Abstract:

Objective The paper aims to reduce the mechanical damage of long staple cotton caused by during mechanical processing. Exploring the changes of physical properties and morphological transition under different mechanical process parameters.

Method The tensile test of long-staple cotton fiber was conducted on tensile tester,and the mechanical properties and morphological changes of fiber samples during the tensile process were analyzed. The test temperature was (21±2) ℃ and the relative humidity was (65±5)%. The influence of fiber diameter, specimen length and tensile speed on the mechanical properties and morphological changes was investigated using a single factor method. The response surface regression model of the interaction of three factors was analyzed and established by the response surface method. The morphology of cotton fiber fractures with different fracture methods was analyzed by scanning electron microscopy.

Results The breaking strength decreased gradually with increasing diameter when the length and tensile speed of cotton fibers remain unchanged. It was found that the diameter and surface morphology are related to the maturity of the fibers, the breaking strength increased with the increasing tensile speed for the same diameter, and minor defects appeared along the tensile direction. As the load further increases, the cracks gradually growth due to a large number of defects accumulated and leading to fiber breakage. The tensile speed and length of fiber have a great influence on the fracture strength, the breaking strength of fiber increases with the increase of tensile speed while decreases with the increase of length. The breaking strength is 38.48 mN for the length of 1 mm and tensile speed of 2 μm/s, and 52.63 mN for the speed of 6 μm/s. The mechanical properties of fibers affected by the three factors mentioned above, and the interaction of them in the order of fiber diameter > tensile speed > sample length. When the load is small during the stretching process, the break elongation and tensile speed of fibers did not have much effect, but both of them increased as the sample length increasing. Furthermore, the two forms of breakage of cotton fibers during stretching often occur. One is that the fiber tension increases with stretching and suddenly breaks when it reaches the maximum bearing tension of cotton fiber. The second is that the tensile force increases firstly to the peak value, then suddenly drop to a certain tensile force and continue for a period of time and then drop to zero. The load-tension curves of fibers showed direct and gradual fracture during stretching, which was related to the initial morphology and the degree of defects of the cotton fibers.

Conclusion The experimental results indicate that the tensile morphology changes of long-staple cotton fiber mainly presented as longitudinal microfibril splitting and propagation in the fiber, and the fracture mode included direct fracture, axial tear, torsional fracture and interfilament slip. The research results will helpful for reducing fiber damage during mechanical processing.

Key words: single long-staple cotton fiber, mechanical property, fracture mechanism, fracture morphology, Xinjiang cotton

CLC Number: 

  • TS562

Fig. 1

Schematic dagram of three long staple cotton fibers side by side and rigid liner box frame glue fixation"

Fig. 2

Drawing part of visual fiber tensioner. (a) Top observation diagram; (b) Side observation diagram; (c) Single cotton fiber installed in clamp; (d) Top view of fiber clamp"

Tab. 1

Test factors and levels"

水平 A
纤维长度/mm		 B
纤维直径/μm		 C
拉伸速度/(μm·s-1)
-1 1 13.42 2
0 3 18.61 4
1 5 22.64 6

Fig. 3

Diameter and frequency distribution of single long-staple cotton fiber"

Fig. 4

Effect of diameter of single long-staple cotton fiber on breaking strength"

Fig. 5

Load-displacement curves of single long-staple cotton fiber under different diameters"

Fig. 6

Effect of tensile velocity and specimen length on breaking strength of single long-staple cotton fiber"

Tab. 2

Response surface test scheme and results"

试验号 A B C 断裂强力/mN
1 0 0 0 47.1
2 1 1 0 41.2
3 0 0 0 45.5
4 -1 0 1 43.6
5 1 0 1 36.9
6 0 0 0 43.7
7 1 0 -1 33.9
8 0 0 0 45.8
9 0 -1 1 38.5
10 -1 1 0 45.8
11 0 1 -1 36.4
12 -1 -1 0 38.4
13 -1 0 -1 34.7
14 0 0 0 44.9
15 0 -1 -1 31.3
16 1 -1 0 30.4
17 0 1 1 50.7

Tab. 3

Analysis of variance with breaking strength as an indicator"

方差源 平方和 自由度 均方 F值 P值
模型 560.58 9 62.29 43.93 0.000 1
A 65.82 1 65.82 46.42 0.000 3
B 157.53 1 157.53 111.11 0.000 1
C 137.39 1 137.39 96.90 0.000 1
AB 2.89 1 2.89 2.04 0.196 4
AC 19.65 1 19.65 13.86 0.007 4
BC 12.60 1 12.60 8.89 0.020 5
A2 50.34 1 50.34 35.50 0.000 6
B2 31.33 1 31.33 22.10 0.002 2
C2 30.44 1 30.44 21.47 0.002 4
残差 9.93 7 1.42
失拟项 3.73 3 1.24 0.80 0.554 6
纯误差 6.20 4 1.55
总和 570.50 16

Fig. 7

Multifactor interaction response surface curves. (a) Influence of fiber length and diameter on breaking strength; (b) Influence of fiber diameter and tensile speed on breaking strength; (c) Effect of specimen length and tensile velocity on breaking strength"

Fig. 8

Effect of specimen length and tensile speed on elongation at break"

Fig. 9

Typical 2 types of cotton fiber tensile mechanical curves. (a) Direct fracture tensile mechanical curve; (b) Progressive fracture tensile mechanical curve"

Fig. 10

Morphological changes during stretching process of a single long-staple cotton fiber. (a) Direct breaking process of single long staple cotton fiber; (b) Gradual breaking of a single long staple cotton fiber"

Fig. 11

Single long-staple cotton fiber fracture end morphology. (a)Direct fracture; (b) Axial tear; (c) Torsional fracture; (d) Slip fracture"

[1] 田景山, 王文敏, 王聪, 等. 机械采收方式对新疆棉品质的影响[J]. 纺织学报, 2016, 37(7): 13-17.
TIAN Jingshan, WANG Wenmin, WANG Cong, et al. Influence of mechanical harvesting methods on Xinjiang cotton quality[J]. Journal of Textile Research, 2016, 37(7): 13-17.
[2] 李孝华, 王瑞霞, 王扬, 等. 新疆机采棉加工中短纤维率变化分析[J]. 中国棉花, 2021, 48(12): 28-31.
doi: 10.11963/cc20210203
LI Xiaohua, WANG Ruixia, WANG Yang, et al. Analysis of short fiber rate change in Xinjiang machine picked cotton processing[J]. China Cotton, 2021, 48(12): 28-31.
doi: 10.11963/cc20210203
[3] 张慧卿, 巴都木. 棉纤维微观结构的形成过程及对纤维性能的影响[J]. 中国纤检, 2008(6):52-55.
ZHANG Huiqing, BA Dumu. The formation process of cotton fiber microstructure and its influence on fiber properties[J]. China Fiber Inspection, 2008(6):52-55.
[4] 连素梅, 罗忻, 李朋, 等. 棉纤维微观结构及其性能概述[J]. 中国棉花, 2018, 45(4): 4-7, 23.
doi: 10.11963/1000-632X.lsmnzy.20180425
LIAN Sumei, LUO Xin, LI Peng, et al. Overview of the microstructure and properties of cotton fiber[J]. China Cotton, 2018, 45(4): 4-7, 23.
doi: 10.11963/1000-632X.lsmnzy.20180425
[5] 刘大彪, 何玉明, 胡鹏, 等. 单纤维微拉伸力学性能测试与分析[J]. 实验力学, 2012, 27(1): 61-69.
LIU Dabiao, HE Yuming, HU Peng, et al. Measurement and analysis of micro tensile mechanical properties of single fiber[J]. Experimental Mechanics, 2012, 27(1): 61-69.
[6] 张治理. 棉纤维的形成特点与其力学特性[J]. 中国纤检, 2004(12): 35-36.
ZHANG Zhili. Formation characteristics and mechanical properties of cotton fiber[J]. China Fiber Inspection, 2004(12): 35-36.
[7] 罗聪. 单纤维拉伸性能测试影响因素的分析[J]. 中国纤检, 2013(1): 60-62.
LUO Cong. Analysis of influencing factors of single fiber tensile property test[J]. China Fiber Inspection, 2013(1): 60-62.
[8] JAYNE B A. Some mechanical properties of wood fibers in tension[J]. Forest Products Journal, 1960, 10(6): 316-322.
[9] LISSEK F, HAEGER A, KNOBLAUCH V, et al. Acoustic emission for interlaminar toughness testing of CFRP: evaluation of the crack growth due to burst analysis[J]. Composites Part B: Engineering, 2018, 136(1): 55-62.
doi: 10.1016/j.compositesb.2017.10.012
[10] 黄淑珍. 扫描电镜下棉纤维的断裂形态[J]. 中国纤检, 1982(3): 19-25.
HUANG Shuzhen. Fracture morphology of cotton fiber under scanning electron microscope[J]. China Fibre Inspection, 1982(3): 19-25.
[11] 杨序纲, 孙文奇. 纤维的形变和断裂:Ⅱ:棉纤维拉伸形变和断裂的形态学和机理[J]. 东华大学学报, 1989, 15(4): 27-33.
YANG Xugang, SUN Wenqi. Fiber deformation and fracture: Ⅱ: morphology and mechanism of tensile deformation and fracture of cotton fiber[J]. Journal of Donghua University, 1989, 15(4): 27-33.
[12] 李繁亭, 程正迪, 张瑜. 纤维的断裂过程和机理[J]. 上海纺织工学院学报, 1980(3): 109-124.
LI Fanting, CHENG Zhengdi, ZHANG Yu. Fracture process and mechanism of fiber[J]. Journal of Shanghai Institute of Textile Technology, 1980(3): 109-124.
[13] 刘鹏飞, 郑津洋, 陶伟明, 等. 伴随纤维断裂的界面分离能的研究[J]. 自然科学进展, 2006, 16(9): 1087-1092.
LIU Pengfei, ZHENG Jinyang, TAO Weiming, et al. Research on interfacial separation energy accompanying fiber fracture[J]. Progress in Natural Science, 2006, 16(9): 1087-1092.
[14] 罗蕾, 嵇醒. 单向复合材料纤维断裂对局部应力集中的影响[J]. 上海力学, 1994, 15(2): 40-51.
LUO Lei, JI Xing. Influence of fiber fracture on local stress concentration in unidirectional composites[J]. Shanghai Mechanics, 1994, 15(2): 40-51.
[15] 于伟东. 纤维弱节的力学特征与判定[J]. 东华大学学报, 2003, 29(2): 32-36.
YU Weidong. Mechanical characteristics and determination of weak fiber nodes[J]. Journal of Donghua University, 2003, 29(2): 32-36.
[16] 钟群鹏, 赵子华, 张峥. 断口学的发展及微观断裂机理研究[J]. 机械强度, 2005(3): 358-370.
ZHONG Qunpeng, ZHAO Zihua, ZHANG Zheng. Development of fractography and study on micro fracture mechanism[J]. Mechanical Strength, 2005(3): 358-370.
[17] 王贤洁. 棉纤维断裂形态学的电子显微研究[J]. 国外纺织技术(纺织分册), 1981(26): 30-31.
WANG Xianjie. Electron microscopic study of cotton fiber fracture morphology[J]. Foreign Textile Technology (Textile Volume), 1981(26): 30-31.
[1] GU Jinjun, WEI Chunyan, GUO Ziyang, LÜ Lihua, BAI Jin, ZHAO Hanghuiyan. Preparation and performonce of cotton stalk bast microcrystalline cellulose/modified graphene oxide composite flame-retardant fiber [J]. Journal of Textile Research, 2024, 45(01): 39-47.
[2] CHEN Meiyu, LI Lifeng, DONG Xia. Mechanical properties of long carbon chain polyamide 1012 fiber at different temperature fields [J]. Journal of Textile Research, 2023, 44(11): 9-18.
[3] YANG Qiliang, YANG Haiwei, WANG Dengfeng, LI Changlong, ZHANG Lele, WANG Zongqian. Fabrication and oil absorbency of superhydrophobic and elastic silk fibroin fibrils aerogel [J]. Journal of Textile Research, 2023, 44(09): 1-10.
[4] ZHANG Ying, SONG Minggen, JI Hong, CHEN Kang, ZHANG Xianming. Influence of heat-setting process on structure and properties of high-tenacity polyester industrial yarns [J]. Journal of Textile Research, 2023, 44(09): 43-51.
[5] SUN Mingtao, CHEN Chengyu, YAN Weixia, CAO Shanshan, HAN Keqing. Influence of needling reinforcement frequency on properties of jute/polylactic acid fiber composite sheets [J]. Journal of Textile Research, 2023, 44(09): 91-98.
[6] ZHAO Mingshun, CHEN Xiaoxiong, YU Jinchao, PAN Zhijuan. Spinning and microstructure and properties of photochromic polylactic acid fibers [J]. Journal of Textile Research, 2023, 44(07): 10-17.
[7] DUAN Chenghong, WU Gangben, LUO Xiangpeng. Mechanical properties of carbon fiber reinforced epoxy resin woven composites based on DIGIMAT [J]. Journal of Textile Research, 2023, 44(07): 126-131.
[8] JIANG Zhiming, ZHANG Chao, ZHANG Chenxi, ZHU Ping. Preparation and properties of flame-retardant viscose fabrics modified with phosphated polyethyleneimine [J]. Journal of Textile Research, 2023, 44(06): 161-167.
[9] SONG Jie, CAI Tao, ZHENG Fuer, ZHENG Huanda, ZHENG Laijiu. Research on supercritical CO2 waterless dyeing property of polyester knitted shoe materials [J]. Journal of Textile Research, 2023, 44(05): 46-53.
[10] LUO Hailin, SU Jian, JIN Wanhui, FU Yaqin. Process optimization of novel silk reeling technique [J]. Journal of Textile Research, 2023, 44(04): 46-54.
[11] HUANG Wei, ZHANG Jiayu, ZHANG Dong, CHENG Chunzu, LI Ting, WU Wei. Property characterization and comparative analysis of Lyocell fibers [J]. Journal of Textile Research, 2023, 44(03): 42-48.
[12] JIANG Bochen, WANG Yue, WANG Fujun, LIN Jing, GUO Aijun, WANG Lu, GUAN Guoping. Correlation of braiding parameters and mechanical properties of mechanically braided integrated esophageal covered stents [J]. Journal of Textile Research, 2023, 44(03): 88-95.
[13] CHEN Huanhuan, CHEN Kaikai, YANG Murong, XUE Haolong, GAO Weihong, XIAO Changfa. Preparation and properties of polylactic acid/thymol antibacterial fibers [J]. Journal of Textile Research, 2023, 44(02): 34-43.
[14] WANG Shudong. Structure and mechanical properties of three-dimensional porous biodegradable polymer artificial esophageal scaffold [J]. Journal of Textile Research, 2022, 43(12): 16-21.
[15] ZHANG Shucheng, XING Jian, XU Zhenzhen. Preparation and properties of multilayer sound absorption materials based on waste polyphenylene sulfide filter materials [J]. Journal of Textile Research, 2022, 43(12): 35-41.
Viewed
Full text


Abstract

Cited
  Shared   
  Discussed   
No Suggested Reading articles found!
京ICP备14006648号
Copyright 2021 © Editorial office of Journal of Textile Research
Supported by Beijing Magtech Co.Ltd