Loading...

Table of Content

    15 January 2009, Volume 30 Issue 01
    • 纤维材料
      Rheological behavior of cellulose carbamate solution
      Halidan MAMAT;Wumanjiang
      JOURNAL OF TEXTILE RESEARCH. 2009, 30(01):  1-4. 
      Abstract ( 1119 )   PDF (323KB) ( 410 )   Save
      Related Articles | Metrics
      The rheological behavior of cellulose carbamate solution and influencing factors were studiedThe results showed that cellulose carbamate in sodium hydroxide solution whose nitrogen contents below 3.57% exhibited shear thinning fluid and its non—Newtonian index less than 1 and these values decreased as the content of CC increased; The index of apparent viscosity was increased as shearing rate increased , and appeared exponential hypotaxis, and experiential formula was obtained; The index of structural viscosity increased slowly as the content of CC increased, and appeared non- linearity increase as the content of CC increased, the rheological behavior became worse as the content of CC was over 5.66%; The pri-spinning temperature of the CC solutions had significant impact on the rheological behavior and it became worse when the temperature was 15℃; the rheological behavior of this solution also turned worse when it was in gel state .
      Mechanical properties of UHMWPE fiber under geating state
      RAO Jue;XU Weilin
      JOURNAL OF TEXTILE RESEARCH. 2009, 30(01):  5-8. 
      Abstract ( 870 )   PDF (569KB) ( 437 )   Save
      Related Articles | Metrics
      The mechanical properties of UHMWPE (Ultra-High-Molecular-Weight-Polyethylene) fiber when subjected to heating at different temperatures in a given time (5 seconds) were discussed. The results showed that with the increase of temperature, the strength,breaking elongation, modulus and work of rupture of the fiber are all decreased to a certain extent. Especially the strength and work of rupture decreased sharply,but the breaking elongation only changed slightly. The optical microscope of QUESTER showed that the longitudinal fracture morphology of the fiber when treated at different temperatures were different. With the increasing of temperature, the microfibril which had caused by the weak force of macromolecule remained no more, but the fine cervical and microporous part appeared. This demestrated that the UHMWPE fiber is poor in heat resistance. The higher the temperature, the easier the fiber breaks.
      Research on reaction kinetics of MC polyamide 6/Kevlar fiber composites
      ZHENG Yuying;WANG Canyao
      JOURNAL OF TEXTILE RESEARCH. 2009, 30(01):  9-12. 
      Abstract ( 1275 )   PDF (499KB) ( 412 )   Save
      Related Articles | Metrics
      The reaction kinetics of MC nylon 6 and MC nylon 6/ Kevlar fiber composites was obtained by differential equations of nonisothermal kinetics and modified by considering the temperature field. The reaction activation energy of MC nylon 6 and MC nylon 6/ Kevlar fiber composites changed from 90.3 kJ·mol-1 and 102.4 kJ·mol-1 to 72.9 kJ·mol-1 and 80.1 kJ·mol-1 after modified, the frequency factor changed from 1.76×109 and 4.02×1010 to 1.26×107 and 9.18×107 accordingly, both of the treating activation energy and frequency factor were closer to the real system. KF could increase the value of activation energy and frequency factor for MC nylon 6. The reaction orders of MC nylon 6 and MC nylon 6/ Kevlar fiber composites are approximately first-class.
      Study on antibacterial properties and cytotoxicity of seacell
      XU Shuiling
      JOURNAL OF TEXTILE RESEARCH. 2009, 30(01):  13-17. 
      Abstract ( 1136 )   PDF (593KB) ( 488 )   Save
      Related Articles | Metrics
      In order to determine the antibacterial properties and cytotoxicity of the silver nanoparticlesfilled seacell fibers, the qualitative and quantitative inhibition trials of the silver nanoparticlesfilld seacell fibers against Staphylococcus aureus and Escherichia coli are investigated. The cytotoxicity tests of the silver nanoparticles on the L-02 cell lines are conducted to evaluate the safty with MTT cytotoxity assay. The results showed that more than 75 % bacteria are inactivated when Staphylococcus aureus (ATCC 25923) and Escherichia coli (ATCC 25922) are incubated with 0.2% silver nanoparticles-filled seacell fibers for 4 hrs . MTT cytotoxicity test showed that the cell relative growth rates are over 90.0% and the cytotoxicity is about 1 degree (no MTT cytotoxity) when the L-02 cell lines are incubated with silver nanoparticles at 37°C under 5% CO2 for 72hrs. The silver nanoparticles-filled seacell fibers show high antibacterial properties and less cytotoxicityl and can be used as a new type of textile material.
      Influence of degumming methods on constituents and structure of cotton bast fibers
      YANG Zhen; ZHANG Yugao; SHI Wei;FENG Xinxing;CHEN Jianyong
      JOURNAL OF TEXTILE RESEARCH. 2009, 30(01):  18-21. 
      Abstract ( 1104 )   PDF (691KB) ( 501 )   Save
      Related Articles | Metrics
      Chemical constituents in different parts of cotton bast fiber were studied. The different degumming methods for cotton bast fiber, such as retting, degumming with normal pressure, and degumming with high pressure were investigated, and the chemical constituents of degummed cotton bast fiber were also discussed in this work. The experimental results demonstrated that after high pressure degumming, the contents of hemi-cellulose and lignin of the cotton bast fiber have reduced obviously. The content of cellulose is increased. Length and fineness of cotton bast fiber after different degumming methods were measured. The morphology and structure of degummed cotton bast fiber were examined by SEM, FTIR and WAXD analysis. Meanwhile, the stress and strain of the degummed fibers were also tested, and rupture curve was shown. Then, on the basis of the experimental data, a better degumming method was determined.
      Structure and properties of PET fibers with nano-mineral praticles
      Ye Jing
      JOURNAL OF TEXTILE RESEARCH. 2009, 30(01):  22-25. 
      Abstract ( 1011 )   PDF (652KB) ( 461 )   Save
      Related Articles | Metrics
      PET fibers with nano-mineral particles were prepared by mixing nano-mineral particles with PET pellets and subsequent alkali weight reduction. SEM observation for the surface and cross section of the fibers showed that the mineral particles with a small size dispersed from the surface to the inner of the fibers, which had apparent microcellular structure. With the addition of nano-mineral particles, there was no change for the crystalline allomorphs of the PET fibers, but its crystallite size increased, moreover crystallinity and degree of orientation decreased. Compared with common PET fibers, the breaking strength of PET fibers with nano-mineral particles decreased, but its breaking elongation and work of rupture increased, especially its capability of transmitting moisture improved markedly whereas mass specific resistance reduced evidently.
      纺织工程
      Entropy change phenomenon during forming of textured yarn
      JOURNAL OF TEXTILE RESEARCH. 2009, 30(01):  26-28. 
      Abstract ( 893 )   PDF (606KB) ( 437 )   Save
      Related Articles | Metrics
      The forming of yarn is characterized by the changes of the space arrangement orderliness of the short fibers or the filaments, so there exists the entropy change phenomenon. The entropy spinning theory would discuss the direction and the limitation of spinning. According to the different entropy changing directions the whole spinning system could be divided into two parts: the entropy producing system and the entropy reducing system, and consequently an entropy change modal could be built up, this supposes a possibility to quantify the relationship between the entropy change and the statement change of fibers’ arrangement in the system. Many experiments indicated that the entropy change, which is the basic reason for the 3-dimensional geometry structure and properties changes of the yarn during spinning, has an internal link with the resultant yarn’s quality. So the researching work on the spinning entropy change theory is of vital importance for the yarn’s quality control and the yarn’s properties design, as well as for developing new spinning methods
      Structure and tensile characteristics of rotor-spun composite yarns
      ZHANG Haixia;ZHANG Xichang;WANG Shanyuan
      JOURNAL OF TEXTILE RESEARCH. 2009, 30(01):  33-36. 
      Abstract ( 1719 )   PDF (698KB) ( 446 )   Save
      Related Articles | Metrics

      For discovering the relationship between structure and tensile properties of rotor-spun composite yarns, the yarn structure and tensile characteristics were investigated by theoretical and experimental methods, and the morphology of yarn breakage ends were observed by the Questar Hi-scope video microscope system. The results indicate that the structure of composite yarns depends on the difference between the filament tension and the tension of staple fiber strand. By controlling the filament over-feed ratio, different kinds of composite yarns can be produced under the constant conditions of normal rotor spinning. The tensile process and breakage ends morphology of composite yarns are related to the yarn structure. Compared with the normal rotor-spun yarn, the tensile properties of composite yarns are improved.

      Quality evaluation of knitting yarns using modified FKCM
      LIU Hao;CHENG Ling
      JOURNAL OF TEXTILE RESEARCH. 2009, 30(01):  37-41. 
      Abstract ( 1348 )   PDF (705KB) ( 14911 )   Save
      Related Articles | Metrics
      In order to evaluate more objectively the performance of knitting yarns, a method using modified fuzzy kernel C-Means (FKCM) clustering algorithm for processing and analyzing of knitting yarns is proposed, in which, the data of low dimension input space is mapped to high dimension feature space, FCM clustering algorithm is performed in the feature space, then the Kernel F clustering validity index is designed for seeking the fitness clustering number, and the corresponding relationship model of class sequence numbers and quality grades is constructed. By analyzing the IRIS Dataset, the result shows the modified FKCM has obtained better classification effect. When it is applied to measuring dataset, and KF index indicates it is reasonable to classify the samples into two kinds. According to the constructed relation of classes and quality grades, the quality grade of each class is acquired. The combination of modified FKCM and KF index provides an efficient data analysis method for multi-index dataset.
      Analysis of surface unevenness of knitted fabrics made with PTT/PET bi-component filaments
      JIAO Qingbao;LUO Jin;ZHOU Sumeng;WANG Fumei;LOU Qingming
      JOURNAL OF TEXTILE RESEARCH. 2009, 30(01):  42-45. 
      Abstract ( 1148 )   PDF (730KB) ( 405 )   Save
      Related Articles | Metrics
      To study the unevenness on the surface of PTT/PET plain knitted fabric, seamless knitted fabrics with PTT/PET were woven on trial basis. The “random strip unevenness” which couldn’t be eliminated by technical adjustments on the surface of PTT/PET plain fabrics was analyzed by studying the original configuration of PTT/PET and the configuration of PTT/PET after simulated finishing process. It was found that the three-dimensional endless spiral crimps of PTT/PET is the cause of “random strip unevenness”. Based on this, a new kind of PTT/PET filaments was made by improving the spinning process. The “random strip unevenness” was disappeared on the surface of knitted fabric made of the new PTT/PET filaments, and it appears uniform and aesthetic.
      Realization of mathematical model for leno weaves
      ZHAN Xin;ZHU Chengyan
      JOURNAL OF TEXTILE RESEARCH. 2009, 30(01):  46-50. 
      Abstract ( 1060 )   PDF (832KB) ( 338 )   Save
      Related Articles | Metrics
      In order to shorten the design of leno weave, this paper put forward a mathematic model for leno weaves. By analyzing the principle of leno weave, the threading chart can be divided into five sectors, weave diagram, leno lifting plan, common lifting plan, leno chain draft, and common chain draft. Using the matrix principle, we can abstract the weave matrix from the leno weave. According to the relationship of five sectors, we can put forward a mathematical model for leno weave. Finally we use the VB.net project system to prove the exactitude of the mathematical model. The mathematical model will be a basic theory for the CAD system of leno weave.
      Analysis of fabric drape evaluation based on support vector machine
      LIN Zhigui; FANG Wei; HUANG Weizhi
      JOURNAL OF TEXTILE RESEARCH. 2009, 30(01):  51-54. 
      Abstract ( 977 )   PDF (747KB) ( 368 )   Save
      Related Articles | Metrics
      For reasons that it is difficult to develop a non-linear model for the evaluation of the fabric drap and the conventional evaluation method can not achieve the desired accuracy of it. The paper, in light of the features of fabric drape data, has proposed a Mercer kernel model for fabric drape assessment. It has proven by experiment and comparison that the precision of the fabric drape has increased by the new method and the assessment model based on Mercer kernel model is feasible. It also shows that different parameter values selected affect the assessment results.
      Comparing artificial neural network and fuzzy theory in the efficiency forecast of worsted loom
      LIU Qian;WANG Yuliang
      JOURNAL OF TEXTILE RESEARCH. 2009, 30(01):  55-59. 
      Abstract ( 979 )   PDF (797KB) ( 362 )   Save
      Related Articles | Metrics
      The artificial neural network technology and fuzzy theory used to forecast the weaving process of worsted fabric were introduced. The main jobs for setting up two kinds of forecast models, i.e., BP artificial neural network and fuzzy evaluation models for weaving process were put forward. And the two different models to predict the loom efficiency were given. The aim was to compare the characteristics of these two models for forecasting weaving quality of wool worsted. The results showd that the character of the neural network forecast model is better than that of the fuzzy evaluation forecast model for the weaving process of wool worsted. And the two theories had their own adaptability for solving the nonlinear problems.
      染整与化学品
      Preparation of functional textiles with nano ZnO/polysiloxane particles and their stability
      GUAN Fanglan
      JOURNAL OF TEXTILE RESEARCH. 2009, 30(01):  64-67. 
      Abstract ( 1067 )   PDF (819KB) ( 402 )   Save
      Related Articles | Metrics
      The nano ZnO/polysiloxane combined coating material was prepared by referring previous research works and applied onto textiles by coating to get functional fabrics. TEM and laser grain size analyzer was used to examined the particle size and distribution of the coating material on the fabric. Atomic absorption spectrophotometer was used to examine the migration of Zn2+ in alkaline synthetic perspiration washing of the functional fabric. The results showed that the average particle size of the material was 103nm, with 70% less than 100nm. The particles exhibited a bursiform structure. The Zn2+of the coating material showed a powerful washability in alkaline synthetic perspiration, which proved that the prepared coating material was stable in alkaline synthetic perspiration.
      Application of transgluaminase to remedy of wool damage
      ZHANG Ruiping;CAI Zaisheng
      JOURNAL OF TEXTILE RESEARCH. 2009, 30(01):  68-71. 
      Abstract ( 1285 )   PDF (817KB) ( 452 )   Save
      Related Articles | Metrics
      Wool fabrics` were finished with TG enzyme in order to decrease the damage of wool resulting from anti-felting treatment with protease. The remedy effect of TG enzyme to the damage of wool was studied. It was shown that TG enzyme can remedy the damage of wool caused by chemical pre-treatment and protease anti-felting finishing, increasing wool fabric strength and decreasing the alkali solubility. TG was capable of catalyzing covalent crosslinking of wool proteins. The optimum protease/TG anti-felting finishing conditions: dosage of protease, 1%(o.w.f.); time, 30min; pH=8~9; dosage of TG, 2%(o.w.f); time, 50min; pH=6~7; bath radio 20:1; and temperature, 50℃. The percentage area shrinkage of the wool fabric treated by this optimal process was 2.93%, the strength was 380.4N and the loss in strength was controled within 7.4%.
      Preparation and properties of water-borne polyurethane for texttles
      TIAN Tao;DUAN Hui-li;WU Jin-hui;HAO Li-mei;YANG Jing-quan
      JOURNAL OF TEXTILE RESEARCH. 2009, 30(01):  72-76. 
      Abstract ( 1122 )   PDF (843KB) ( 387 )   Save
      Related Articles | Metrics
      A kind of water-borne polyurethane used for fabrics was synthesized by self emulsification method, with PEG、PPG、TDI、DMPA and BD as raw materials, and hydrophilic polyurethane coating composite material was prepared further. The influences of temperature and reaction time of prepolymerization, n(-NCO): n(-OH), amount of DMPA, neutralization mode, and emulsification method etc on the properties of water-borne polyurethane emulsion were studied, and the waterproof capability, moisture permeability and biological protection capability of the composite material were tested. The results indicated that this kind of polyurethane had good integrative performances, and the hydrophilic coating composite could provide good waterproof function, moisture permeability and biological protection capability.
      Influence of supercritical CO2 treatment on the poperties of polylactic acid fiber
      YANG wenfang;ZHNG Zhiqiu;SU Zhiwu
      JOURNAL OF TEXTILE RESEARCH. 2009, 30(01):  77-81. 
      Abstract ( 1069 )   PDF (843KB) ( 494 )   Save
      Related Articles | Metrics
      supercritical CO2 fluid;polylatic acid fiber;breaking strength;melting point; crystallinity;degree of orientation
      Application of Fe modified PAN fibrous catalyst to degradation of azo dyes
      HAN Zhenbang;DONG Yongchun;DU Fang;LIU Chunyan
      JOURNAL OF TEXTILE RESEARCH. 2009, 30(01):  82-87. 
      Abstract ( 1264 )   PDF (874KB) ( 438 )   Save
      Related Articles | Metrics
      Polyacrylonitrile (PAN) fiber was modified by hydrazine and hydroxylamine to enable ligation of ferric ions to the fiber surface so as to produce a Fe-modified PAN fibrous catalyst (PAN-Fe) for the oxidative degradation of two soluble anionic azo dyes in the presence of H2O2. The dosage of catalysts, ferric ion content loading on catalyst, dye concentration and pH values on the photocatalytic decoloration of two azo dyes in water were investigated in this paper. The results indicated that PAN-Fe catalyst has a significant catalytic property on oxidative degradation of two azo dyes, especially under light irradiation. Increasing the dosage of catalysts and enhancing ferric ion content lead to high decoloration level. Moreover, the decoloration of two azo dyes is developed in the presence of the catalysts under alkaline condition, but increasing concentration of dyes in solution causes the low decoloration percentage.
      Applications of happening color in Chinese blue calico’s innovative design
      PAN Chunyu;GAO Weidong
      JOURNAL OF TEXTILE RESEARCH. 2009, 30(01):  88-90. 
      Abstract ( 1260 )   PDF (912KB) ( 530 )   Save
      Related Articles | Metrics
      For protecting and developing the Chinese blue calico technology, technological innovation should be made so as to meet the developing trends on today’s textile market. Therefore, it has positve significance to reevaluate the advantages and unique features of Chinese blue calico. Introducing the happening color into the innovative concept, this paper elucidates the innovative design in terms of indigotin, printing, pattern and fabric, pointing out that the vivid and personified happening color is an effective tool to change the traditional style of Chinese blue calico and enhance its competitive power on the marlet. The advantages and drawbacks of the traditional manual printing of Chinese blue calico are discussed, along with the features of its color, process, design and material.
      Preparation of thermochromic finishing agent
      WU Zanmin;LV Xiaozhuo;FENG Wenzhao
      JOURNAL OF TEXTILE RESEARCH. 2009, 30(01):  91-96. 
      Abstract ( 1393 )   PDF (928KB) ( 653 )   Save
      Related Articles | Metrics
      In order to enhance the stability and reversibility of thermochomic materials,using melamine resin as the wall materials, and the crystal violet lactone-stearic acid and tetradecanol as the core, and adding emulsifying agent and xanthan gum aqueous solution as the protective colloid, organic thermal materials are prepared and microencapsulted. Preparation technics:the mass of emulsifier is 2%, super ultrasonic emulsified time is 30min, the ratio of core and shell is 2:1, the rate of stirring is 720r/min and the temperature of reaction is 70℃. The temperature of color changing of the microcapsule is 46℃, while the time of color changing is 25s, and the temperature and the time of color fading are 40℃ and 49s, and its color change reversibly can be effected between purple and light yellow.
      服装工程
      Processing technology of tiger head imitation cap in the central area of China
      ZHANG Jingqiong;ZHANG Jisheng;SUN Ningning
      JOURNAL OF TEXTILE RESEARCH. 2009, 30(01):  97-101. 
      Abstract ( 1115 )   PDF (1010KB) ( 387 )   Save
      Related Articles | Metrics
      This article discussed the fabricating craft of the tiger head imitation cap in the central area of China. Through on-the-spot investigation paper patterns, crafts and materials of tiger head imitation caps in the area were researched. In terms of paper pattern, it included the cap body paper pattern and facial features paper pattern which involved the eye, nose, tooth, mouth etc. And related notes and graphics were made. Fabrication steps and methods of the cap body and the facial parts were recorded also. As to materials, recording and analysis covered the face fabric, lining, padding and accessories. On this basis, the characteristics of tiger head imitation caps in the central area of China were summerized.
      Acculturation of Jurchen clothing culture in Jin Dynasty
      GU Yunfen;ZHANG Shu
      JOURNAL OF TEXTILE RESEARCH. 2009, 30(01):  102-106. 
      Abstract ( 1579 )   PDF (998KB) ( 583 )   Save
      Related Articles | Metrics
      Based on the historical records and the files of archaeological discovery, the present paper studies the acculturation of Jurchen clothing culture in Jin Dynasty in different characteristic phases, the factors arose from and the attitude people took. It summarizes that the acculturation of Jurchen clothing culture has different characteristic phases as follows: carrying out sinicization, forming the sedan chair clothing system, the fashion being from simplicity to luxury, improving the sedan chair clothing system and emerging of clothing hierarchical system, calling for the fore ancestor’s style which is thrifty and unvarnished, stopping the sinicization and retaining the Jurchen’s clothing cultural tradition. The factors which promote the acculturation of Juichen clothing culture include political, economic, ideological aspects and so on. People’s attitude towards the acculturation of Jurchen clothing culture included adoption, adaptation and resistance.
      机械与器材
      Reverse design of conjugated cams developed by VB
      ZHU Caiqin;SHEN Yi
      JOURNAL OF TEXTILE RESEARCH. 2009, 30(01):  107-111. 
      Abstract ( 1422 )   PDF (1029KB) ( 580 )   Save
      Related Articles | Metrics
      In the view of the current cam production, most of them are depend on survey data, which can easily create an error, and can also affect the operating performance. For this reason, this paper brings forward a method to reduce the error by fitting the cam profile and develop a reverse design of conjugated cams ‘ system based on Visual Basic (VB). This system takes the three transect interpolation function to smooth the main cam contour line, which can improve the continuity of the curvature, and make another cam’s contour line according to the relationship between the conjugated cams. And then Pro/E is used to make the entity structure of the conjugated cams and do the analyses of the kinematics. By the analysis of the law of the motional curves, the motional angle and laws are determined, and finally, the redesign of the conjugated cams is realized.
      管理与信息化
      Computer simulation for jacquard warp knitted fabric
      CONG Honglian;GE Mingqiao;JIANG Gaoming
      JOURNAL OF TEXTILE RESEARCH. 2009, 30(01):  112-116. 
      Abstract ( 1058 )   PDF (1100KB) ( 1137 )   Save
      Related Articles | Metrics
      The characteristics of Jacquard warp knitted fabric were studied and the colorized design model was offered. The loop structure of the fabric was analyzed and its theoretical model was set up to confirm the number and position of control points of each type of loops. Two methods, i.e., segment and spline cure were used to describe the loop state with fuses on theoretical analysis. In order to show of displacement and distortion of loop, presenting a factual model of the loop. In simulation, considerations were given to information concerning the colorized design, the change of yarn tension resulting from lapping movement, fineness of yarn, color information, and the quality of material. Thus a good simulation was achieved.
      Study and application on fashion design process model based on the integrated environment
      WANG Jun;WANG Zhijun;LIU Xiaogang;YUAN Rong
      JOURNAL OF TEXTILE RESEARCH. 2009, 30(01):  117-121. 
      Abstract ( 1062 )   PDF (1080KB) ( 665 )   Save
      Related Articles | Metrics
      A new optimized fashion design process model is put forward, i.e., substituting the integrated design method for the traditional linear design,and it will effecitively shorten the prcess of fashion design. According to the framework of fashion design process based on concurrent design, fashion design process is divided into several levels, and an effective multi-layers fashion design process model is created. By combining computer programmed calculating method with practical case, the time consumption of the new model is found obviously decreased as compared with traditional model. The practical value of fashion design process model based on the integrated environment is proven by both theory and practice.
      3D clothing fitting research based on feature matching
      LIU Jun;LI Zhong;HU Jueliang
      JOURNAL OF TEXTILE RESEARCH. 2009, 30(01):  122-126. 
      Abstract ( 1145 )   PDF (1094KB) ( 451 )   Save
      Related Articles | Metrics
      This paper presents a 3D clothing fitting via the feature matching. Firstly, the method fits each vertex and its local neighborhood of the clothing and human models by constructing the biquadratic Bezier surface. It can estimate the Gaussian curvature and the mean curvature of each vertex. Then, the feature points of two mesh models are extracted according to curvatures. In order to reduce the wrong matching and avoid the multiple matching relations, it uses the curvature constraint conditions or few interactive operations to obtain the correct corresponding feature points. The coordinate transformation matrix in 3D space is calculated to realize the rough match by the minimal distance function. Finally, the clothing model is scaled and matched again to achieve the accurate matching effect. The experimental results show that the 3D fitting algorithm is convenient and effective.
      Multi-agent prototype implementation of interaction system for fashion E-retail
      WANG Lichuan;CHENG Yan
      JOURNAL OF TEXTILE RESEARCH. 2009, 30(01):  127-130. 
      Abstract ( 1216 )   PDF (1037KB) ( 375 )   Save
      Related Articles | Metrics
      An interactive system for E-retail is designed to meet the requirements of fashion marketing development. The infrastructure and prototype implementation of this system are presented and analyzed. The interactive system is composed of three fundamental modules: recommendation, negotiation and feedback, and is applicable for fashion E-retail. Agent technique is applied on the process of interaction for rapid respondence in this system. To provide the personalized internet service, the system can not only generate real-time recommendation according to the characters of customers, but also collect feedback information and make the dynamic adaptation of customer profiles based on behavioral data and domain knowledge models. This approach is domain-independent and applicable for a wide-variety personalized market of fashion E-retail.
      综合述评
      Advances in the study of evaluation indexes of female physical attractiveness
      ZHAI Lili;QIAN Xiaoming;WANG Rui
      JOURNAL OF TEXTILE RESEARCH. 2009, 30(01):  131-134. 
      Abstract ( 1065 )   PDF (1040KB) ( 495 )   Save
      Related Articles | Metrics
      Body is the fundamentality of garment design, whose precondition is to understand the physical attractiveness. This paper focuses on the determinants of female physical attractiveness based on evolutionary psychology and the relationship between these determinants and physical attractiveness. Three determinants of female physical attractiveness are the waist to hip ratio (WHR), body mass index (BMI) and volume height index (VHI). The degree of physical attractiveness is expressed as attractiveness rating. There is a weak negative correlation between the attractiveness ratings and WHR. The optimal value of WHR for attractiveness is 0.7. The relationship between BMI or VHI and attractiveness ratings is nonlinear. VHI, which is a newest suggested determinant, has not been applied widely.